At Orson Chemicals, we believe in extending our technical expertise to our customers, providing a higher level of problem resolution and advanced implementation guidance.

Awareness and knowledge is a highly crucial focal point in the field of composites. We sincerely educate our customers based on application usage, quality parameters, technical features and recommended procedures to be followed in order for the clients to manufacture high-performance products and effectively overcome workflow challenges.

Frequently Asked Questions

What is the difference between a resin and a gelcoat?

A typical resin has medium viscosity while the gelcoat is a material of higher viscosity. A gelcoat is normally 3 times more thixotropic than a typical resin. This ensures that a layer of recommended thickness can be applied as a single / double coat without any drainage on the given surfaces.

Gelcoat is the outermost layer of the laminate and it applies to the laminate in small quantity (a film size of 500 – 600 µ) this thickness is preferably build up in two coats this layer is used as a protective as well as aesthetic layer to the resin laminate. It also gives the very good cosmetic look to the laminate.

How many coats of mould release agent / wax / pva should be applied to the FRP mould?

The number of coats depends on the performance of the mould and the mould releasing agent. Please read the instructions given by the manufacturer on the mould release agent for the better results. If you are applying wax or PVA at least three to five coats are recommended before start of the moulding and if it is pva then it should be properly dry before moulding .

What is the best combination of resin and mat?

Considering 1 sq. mt. of CSM it is generally recommended to have a resin: glass ratio of 2.5: 1. However it varies from individual to individual; more skilled operators work up to 1.8: 1 ratio also, since they achieve proper wetting and consolidation due to their experience.

How does the concentration of catalyst used depend on the climatic conditions?

The amount of catalyst used is highly dependent on the climatic conditions and hence, the percentage added should varies as per the applicable. Less % of catalyst is used during warm conditions and more % of catalyst is added during cold conditions.

Lowest percentage should not be lesser than 0.8 % ( on the basis of resin ) by the volume of resin and any lower will affect the curing cycle and the laminate will remain under cured. Another option is to get a slower reactivity catalyst though it will extend the gel time of working.

The highest percentage should be 2.5 % by volume of the resin, and any higher will affect the curing cycle. This will lead to fast curing, may caouse  warpage and cracks in the final product.

'I want to cast a clear specimen.’ Can I use a normal GP for it?

Normal clear resin will give you yellow colouring and due to higher exotherm in the normal resin, there might be a chance of cracking or mould may get eroded. Hence, we highly recommend using the specially formulated resin which will have optimum exotherm and will give you clear colour.

Will using a normal pigment from the market in a premium gelcoat affect final product property?

A normal pigment used from the market will definitely alter the properties of the final product. Gelcoat is the outermost and most important protective layer for the final product. Using a normal pigment will promote yellowing and the colour fading after some months of use.

Hense always use pigment pest from the reputed manufacturer.

How much pigment paste do you recommend adding to my gelcoat and resin?

It is generally recommended to add up to 4% by volume of gelcoat for most of the colours, however  it varies depending on the colour and pigment paste concentration.

For the resin, it is recommended to add up to 2-3% by volume of the resin.

How is vinyl ester resin different from normal polyester resin?

A vinyl ester resin has excellent chemical resistance, hydrolytic stability and higher heat resistance. Hence, they are used in areas and applications exposed to the high corrosive atmosphere. However a general polyester resin is not such a high-performance product and its application is limited to certain areas.

Why is it necessary to clean the mould surface?

Your final product design depends on the performance of your mould. It is highly recommended to clean the moulds well before application of release agents as all major product failures, poor surface appearance, or lower production is a result of poor mould performance.

‘I want to make a mould.’ Can I use normal GP?

There are a special set of resins that exhibit specific characteristic properties for mould making and are called as tooling resins and tooling gelcoats that are used in the preparation of the mould. You are only recommended to use such resins for mould making.

‘I want to use carbon fibre for my product.’ What resin is suitable for it?

A general unsaturated polyester resin is having limited compatibility with the carbon and aramid fibre in terms of waiting. Hence, it is always recommended to use only vinyl ester resins and epoxy resins formulated to be compatible with carbon fibre structure.

I am not getting good color finish in my pultruded I-channels, kindly recommends the solutions?

A good finished of the pultruted products is depends on various factors like speed of the line, temperature and the type of LPA use. hense your advice to use Polystyrene type of LPA in your slurry formulation.

While gelcoat application why we are getting creases or foldings on the gelcoated surface?

We can consider this problem interms of wrinkling which is due to impurities in catalyst, solvent and water contamination and also due to over cured surface.

This can be avoided by using good quality catalyst and good quality solvents ( it should be moisture free ). this can be also avoided by lowering the catalyst percentage.

Why we express acid number or acid value on solution basis in composite industry, why not on solid basis?

Acid number is always express on solid basis where polyester resins are use in coating industries since resin will go with the high loading of pigments. in composite industry polyester resin are not really going with the high loading of pigments hence acid number is always express on solution basis.